Menu

Discussion Forum

New Discussion
查找

Discussion ClosedThis discussion was created more than 6 months ago and has been closed. To start a new discussion with a link back to this one,click here.

Fatigue analysis after a Time Dependent study

Posted 2024年2月8日 GMT+1 12:12Heat Transfer, Structural Mechanics, Material Models3 Replies

Iliass Tahiri
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Hello everyone,

I'm running a fatigue simulation after a time dependend (thermal and mechanical) simulation.

The output I'm looking for is the "Fatigue Usage Factor" but in every time step of the time dependend simulation. But it is not the cas! I only have the final value. I'm looking to calculate the evolution of the Fatigue Usage Factor with all time steps.

Can you please let me know if you have a solution to this questions?

Thank you very much in advance. Iliass

3 Replies Last Post 2024年2月15日 GMT+1 11:05
Mats Danielsson COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 7 months ago 2024年2月8日 GMT+1 16:26

Dear Iliass Tahiri,

What type of fatigue feature are you using? Cumulative Damage? Stress-Based?

The short answer is that you cannot currently trace the evolution of the fatigue usage factor with time, but it would be helpful to know more about your particular model setup.

Mats

Dear Iliass Tahiri, What type of fatigue feature are you using? Cumulative Damage? Stress-Based? The short answer is that you cannot currently trace the evolution of the fatigue usage factor with time, but it would be helpful to know more about your particular model setup. Mats
Iliass Tahiri
Send Private Message Flag post as spam

Please login with a confirmed email address before reporting spam

Posted: 7 months ago 2024年2月14日 GMT+1 10:09

Dear Mats,

Thank you for your answer. For now I'm using a cumulative damage fatigue approach since my I have combined mechanical and thermal loads.

One idea I have since it's not possible is to run the model with various time limit, derive the fatigue usage factor at these time limit. Please let me know what you think.

Best regards, Iliass

Dear Mats, Thank you for your answer. For now I'm using a cumulative damage fatigue approach since my I have combined mechanical and thermal loads. One idea I have since it's not possible is to run the model with various time limit, derive the fatigue usage factor at these time limit. Please let me know what you think. Best regards, Iliass
Mats Danielsson COMSOL Employee

Please login with a confirmed email address before reporting spam

Posted: 7 months ago 2024年2月15日 GMT+1 11:05

Dear Mats,

Thank you for your answer. For now I'm using a cumulative damage fatigue approach since my I have combined mechanical and thermal loads.

One idea I have since it's not possible is to run the model with various time limit, derive the fatigue usage factor at these time limit. Please let me know what you think.

Best regards, Iliass

Dear Iliass,

I think it would be good if you contacted our support engineers with your specific case. If you refer to this conversation, I will be in the loop also.

Mats

>Dear Mats, > >Thank you for your answer. For now I'm using a cumulative damage fatigue approach since my I have combined mechanical and thermal loads. > >One idea I have since it's not possible is to run the model with various time limit, derive the fatigue usage factor at these time limit. Please let me know what you think. > >Best regards, >Iliass Dear Iliass, I think it would be good if you contacted our support engineers with your specific case. If you refer to this conversation, I will be in the loop also. Mats

Note that while COMSOL employees may participate in the discussion forum, COMSOL®software users who are on-subscription should submit their questions via theSupport Centerfor a more comprehensive response from the Technical Support team.

Suggested Content

Baidu
map